Envirolak 100 series (warm clear or dark colors)
Envirothane 100 Warm Clear Self-Seal Topcoat EL100XX
EL100XX series is a warm clear urethane topcoat which is also tintable for dark colours. It provides a lasting, durable finish for wooden surfaces that meets or exceeds KCMA standards as a 1k product. The product can also be catalyzed with CAT100-LV hardener or crosslinked with CAT150 crosslinker to improve chemical, scratch, mar resistance and vertical flow. This product combines outstanding toughness and stain resistance with the wood warmth and hand-feel of traditional solvent-based coatings, all in a low VOC water-based finish.
This product is designed for interior wood finishing applications such as tables, bar tops, cabinetry, furniture, flooring, and millwork.
PRODUCT CODES:
EL100XX (EL10005, EL10010, EL10020, EL10030 ,EL10050, EL10090)
NAME:
ENVIROTHANE 100 WARM CLEAR SELF-SEAL TOPCOAT
AVAILABLE SHEENS:
| EL100 05 | 5 Gloss - Deat Flat |
| EL100 10 | 10 Gloss - Flat |
| EL100 20 | 20 Gloss - Low Gloss |
| EL100 30 | 30 Gloss - Satin |
| EL100 50 | 50 Gloss - Semi Gloss |
| EL100 90 | 90 Gloss - High Gloss |
DESCRIPTION:
EL100XX series is a warm clear urethane topcoat which is also tintable for dark colours. It provides a lasting, durable finish for wooden surfaces that meets or exceeds KCMA standards as a 1k product. The product can also be catalyzed with CAT100-LV hardener or crosslinked with CAT150 crosslinker to improve chemical, scratch, mar resistance and vertical flow. This product combines outstanding toughness and stain resistance with the wood warmth and hand-feel of traditional solvent-based coatings, all in a low VOC water-based finish. Only use 100 series over raw wood, Envirostain’s, 170, 170-TB or 180 primers, SEAL300 and as a self seal or over itself as a 1K or 2K with CAT100LV or CAT150. 100 series can also be used over SEAL500 as a 2K with CAT100LV.
USES:
This product is designed for interior wood finishing applications such as tables, bar tops, cabinetry, furniture, flooring, and millwork.
PRODUCT PREPARATION:
Reduction is not required when spraying with Air Assisted Airless or Airless, however, adding 3% RX010 reducer or 5-10% water will improve application characteristics when used as a clear coat. Reduction is reccomended for pressure pots, HVLP turbine, conventional cup guns or brush and roll. Product should be at room temperature and mixed thoroughly prior to application to ensure consistency and gloss. Drill mix any soft settling off the bottom of a can is reccomended.
CATALYST RATIOS USING CAT100-LV HARDENER
| EL100 XX Series | by weight ~10% | by volume ~10% (10:1) |
|---|---|---|
| (approx. 2 hr pot life @10%) | 2.4kg (2 cans) per 19.6kg (5 GA) pail | 2.12L (2 cans) per 5 GA |
| (approx. 4 hr pot life @5%) | 480g (2/5 can) per 3.9kg (1 GA) | 425mL/14.4oz.(2/5 can) per GA |
CATALYST RATIOS USING CAT150 CROSSLINKER
| EL100 XX Series | by weight ~ by volume |
|---|---|
| Per Quart: | 29 grams, 25mL ~ 0.9 fl oz. |
| Per Gallon: | 117 grams, 100mL ~ 3.4 fl oz. |
| Per Pail (5 GA): | 582 grams, 497mL ~ 17 fl oz. |
RECOMMENDED APPLICATION:
| Spray type: Air Assisted Airless | |
|---|---|
| Fluid Pressure: | 500-600 PSI |
| Air Pressure: | 25 PSI (triggered) |
| Tips: Kremlin | 04114, 06114, 09114, 09154 |
| Wagner | 0950, 1150, 1350, 1360, 1380 |
| Graco/CA and others | 411, 413, 511, 513, 611, 613 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: Airless | |
|---|---|
| Fluid Pressure: | 2000-3000 PSI |
| Tips: Fine Finish, Ultra Finish or Skill Tip | 306, 608, 408, 508, 06-17 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: HVLP (Turbine) 5 stage or higher | |
|---|---|
| Air Pressure: | Max |
| Needle: | 1.8-2.0 needle high solids air cap |
| Reduction: | 3-5% ELRX010 or 10-15% water |
| Spray type: Cup Gun (gravity) | |
|---|---|
| Air Pressure: | 25-35 PSI |
| Tips: | 1.8 needle |
| Reduction: | 2-5% ELRX010 or 10-15% Water |
| Brush: | Medium/Firm Nylon or Polyester |
| Roll: | Mohair, Velour or 3/16 Microfiber |
| Reduction: | 3-5% ELRX010 or 10-20% Water |
| Wet Film Build: | 4-6 mils |
|---|---|
| Grams per 1/10 sq. metre: (250x400mm board) | 8.5-13g |
| Number of Coats: | 1-3 depending on desired look |
| Maximum Dry Film Build: | 5 mils |
| Coating Temperature at Application: | 20°C (68°F) or higher |
*for colder temperatures, add reducer (ELRX010) or warm material prior to spraying
PHYSICAL PROPERTIES:
(of the ELDGB100)
Specific Gravity:1.02 ± 2%
Viscosity: 2000-2500 cps. at 20°C
Solids Content: 30% by weight
Pot Life: None
Flash Point: >75°C
VOC’s: 51.2 g/L, 0.43 lbs/gal
VOC’s (less exempt): 150 g/L, 1.25 lbs/gal
SANDING:
Sand raw wood 150- 180 grit to remove any mill glaze, wide belt scratches or oxidation. Sand EL100 XX between coats with 320 or 400 grit sandpaper and refine with superfine sponges.
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 20 Minutes
Dry to Sand: 1-2 Hours
Dry to Stack: 12-16 Hours
Note: Good gentle air movement (not a hurricane) with a recirculator or fan while parts are drying will reduce dry to sand times by 20-40% with reasonable humidity levels (<65% r.h.). Lower temperatures or higher humidity will extend dry times.
Conventional Oven:
(40-45°C/104-113°F)
Dry to Touch: 10 Minutes
Dry to Sand: 30-60 Minutes
Dry to Stack: 3-4 Hours
Sun-Spot IR Cure:
Flash off: 1-2 Minutes
Direct Cure: 5-10 Minutes @60-70°C(140-160°F)
Rack Cure (Indirect no probe mode): 10-30 Minutes @20%+ power
Cool: 10-20 minutes
Product is dry to sand (or stack) after cooling
TYPICAL SYSTEMS:
Stain System:
Substrate: Various Woods, check adhesion on oily woods (teak, ipe, brazilian cherry, etc.) prior to finishing
Sand raw wood with 150 or 180 grit sandpaper and fine sponges
Envirostain wiping, spray, roll coat or dipping stain
EL100XX Topcoat 1K or 2K with CAT100LV or 2K with CAT150
Sand between coats using 320-400 grit sandpaper and refine with superfine sponges 1 or 2 coats
EL100XX Topcoat 1K or 2K with CAT100LV or 2K with CAT150
Substrate: Various Woods, check adhesion on oily woods (teak, ipe, brazilian cherry, etc.) prior to finishing
Sand raw wood with 150 or 180 grit sandpaper and fine sponges
Envirostain wiping, spray, roll coat or dipping stain
1 or 2 coats SEAL500 1K or 2K with CAT100LV
Sand between coats using 320-400 grit sandpaper and refine with superfine sponges 1 or 2 coats EL100XX 2K with CAT100LV
TYPICAL SYSTEMS:
Dark Solid Colours:
Substrate: MDF
ELPR170 White Primer 1K or 2K + 5% 896-9901 Black (makes dark grey)
or ELPR180 Neutral Primer 1K or 2K tinted to any dark color including black
Sand using 320 grit sandpaper and fine or superfine sponges
ELPR170 White Primer 1K or 2K + 5% 896-9901 Black (makes dark grey)
or ELPR180 Neutral Primer 1K or 2K tinted to any dark color including black
Sand using 400 grit sandpaper and refine with superfine sponges
1 or 2 coats EL100XX 1K or 2K with CAT100LV or 2K with Crosslinkeder tinted to dark colour
CLEANING:
Flush all equipment with water until it runs clear. Built-up coating and deep cleaning can be performed using ELRX110 EnviroKlean WB Cleaner. For best results cleaning tips, aircaps and unpainted parts use ELRX110 for one hour or 10-20 minutes in an Ultrasonic bath (max. temp. 50°C/120°F). Do not leave painted parts (i.e. spray guns) in ELRX110 for more than 20 minutes.
GENERAL INFORMATION:
Use stainless steel (304/316) equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.